mirror of
https://gitee.com/Vancouver2017/luban-lite.git
synced 2025-12-17 01:28:54 +00:00
76 lines
2.5 KiB
YAML
76 lines
2.5 KiB
YAML
# Licensed to the Apache Software Foundation (ASF) under one
|
|
# or more contributor license agreements. See the NOTICE file
|
|
# distributed with this work for additional information
|
|
# regarding copyright ownership. The ASF licenses this file
|
|
# to you under the Apache License, Version 2.0 (the
|
|
# "License"); you may not use this file except in compliance
|
|
# with the License. You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing,
|
|
# software distributed under the License is distributed on an
|
|
# "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
|
|
# KIND, either express or implied. See the License for the
|
|
# specific language governing permissions and limitations
|
|
# under the License.
|
|
#
|
|
|
|
syscfg.defs:
|
|
BLEPRPH_LE_PHY_SUPPORT:
|
|
description: >
|
|
Enable support for changing PHY preference on active connection.
|
|
PHY preference change is triggered by configured GPIO pins.
|
|
Current PHY is indicated using LEDs connected to configured
|
|
GPIO pins.
|
|
value: 0
|
|
BLEPRPH_LE_PHY_BUTTON_GPIO:
|
|
description: >
|
|
GPIO pins for changing PHY preference on active connection. This
|
|
is an array of 4 GPIO pin numbers for 1M, 2M, LE Coded S=2 and
|
|
LE Coded S=8 respectively.
|
|
value: "(int[]){ BUTTON_1, BUTTON_2, BUTTON_3, BUTTON_4 }"
|
|
BLEPRPH_LE_PHY_LED_GPIO:
|
|
description: >
|
|
GPIO pins for indicating current PHY on active connection. This
|
|
is an array of 3 GPIO pin numbers for 1M, 2M and LE Coded
|
|
respectively.
|
|
value: "(int[]){ LED_1, LED_2, LED_3 }"
|
|
|
|
syscfg.vals:
|
|
CONSOLE_IMPLEMENTATION: full
|
|
LOG_IMPLEMENTATION: full
|
|
STATS_IMPLEMENTATION: full
|
|
|
|
# Disable central and observer roles.
|
|
BLE_ROLE_BROADCASTER: 1
|
|
BLE_ROLE_CENTRAL: 0
|
|
BLE_ROLE_OBSERVER: 0
|
|
BLE_ROLE_PERIPHERAL: 1
|
|
|
|
# Configure DIS
|
|
BLE_SVC_DIS_FIRMWARE_REVISION_READ_PERM: 1
|
|
|
|
# Log reboot messages to a flash circular buffer.
|
|
REBOOT_LOG_FCB: 1
|
|
LOG_FCB: 1
|
|
CONFIG_FCB: 1
|
|
|
|
# Enable smp commands.
|
|
STATS_MGMT: 1
|
|
LOG_MGMT: 1
|
|
CONFIG_MGMT: 1
|
|
|
|
# OS main/default task
|
|
OS_MAIN_STACK_SIZE: 512
|
|
|
|
# Lots of smaller mbufs are required for smp using typical BLE ATT MTU
|
|
# values.
|
|
MSYS_1_BLOCK_COUNT: 22
|
|
MSYS_1_BLOCK_SIZE: 110
|
|
|
|
BLE_SVC_GAP_DEVICE_NAME: '"nimble-bleprph"'
|
|
|
|
# Whether to save data to sys/config, or just keep it in RAM.
|
|
BLE_STORE_CONFIG_PERSIST: 0
|